Latest Avaya 3600 Real Exam Download 61-70



In a multicast campus, when should the PIM interface in passive mode be configured?


A.      When the ERS 8600 is used as an edge switch and is aggregating end users

B.      When PIM control traffic must be passed

C.      When there are no unicast routing paths

D.      When more than one multicast routing protocol is in use


Correct Answer: A




A split Multi-Link Trunking (SMLT) for switch clustering is being configured.  Which statement is a configuration requirement for the SMLT?


A.      CP-Limit is configured on edge switch stacks.

B.      Neighboring edge switch stacks should be connected to each other via a DMLT connection to add resilient paths in the event of an SMLT failure.

C.      Alternate the primary path of the SMLT connection to load balance the switch core.

D.      VLANS that are defined on the SMLT are so defined on the MLT that defines the core Inter Switch Trunks (IST)


Correct Answer: D




After issuing a show mit ist stats (CLI) or show ist stat (ACLI) command, it is determined that running type is normal MLT and not Inter Switch Trunks (IST).  Which are two causes of the 1ST not running properly? (Choose two.)


A.      The 1ST is not enabled on both switches.

B.      The MLT ID does not match on both switches.

C.      The peer IP address is not the address of the peer switch 1ST VLAN

D.      The peer IP addresses have to be and


Correct Answer: AC




Consider the following port conditions on an Ethernet Routing Switch (ERS) 8648GTRS 10/100/1000

Ethernet I/O module:

Left LED – green

Right LED – flashing green


What is the status of the port?


A.      The link speed is 100 Mbps, and the port is disabled.

B.      The link speed is 1000 Mbps, and the port is disabled

C.      The link speed is 100 Mbps, and the port is passing traffic.

D.      The link speed is 1000 Mbps, and the port is passing traffic.


Correct Answer: D








The attempt to manage an Ethernet Routing switch (ERS) 8600 using a Virtual Router Redundancy protocol (VRRP) address was unsuccessful.  What is causing this problem?


A.      The virtual router identifier is 0.

B.      The data center interface is set as a critical IP interface.

C.      A real IP address is required for management access not a VRRP address.

D.      The incorrect MAC offset is configured for the VRRP address.


Correct Answer: C




A technician is configuring password levels on the Ethernet Routing Switch (ERS) 8600, and wants the manager to be able to view and edit device settings, but not to be able to change security and password settings.  Which Login Level should be set for the manager?


A.      Layer 2 Read-Write Accesses

B.      Layer 3 Read-Write Access

C.      Read-Write-All Access

D.      Read-Write Access


Correct Answer: D




After experiencing issues with XFPs, the show sys pluggable-optical-modules info CLI command is used to find that the switch does not recognize the XFPs.  Which other method can be used to view the XFP compatibility?


A.      Check for port alarms.

B.      Show DWDM-XFP {detail}.

C.      Check the config sys set pluggable-optical-module info.

D.      Select Edit, Port, General, DDI/SFP from the Enterprise Device Manager to see the XFP port specifics_


Correct Answer: D








The exhibit indicates the two show commands from an edge Ethernet Routing Switch (ERS) 5520-24T-PWR an untagged frame arrives on port 10.which is configured as an access port to which VLAN will the packet be forwarded?




A.      All untagged packets will be placed in the default VLAN (VLAN 1).

B.      All untagged packets will be discarded.

C.      All untagged packets will be placed in VLAN 311

D.      All untagged packets will be placed in VLAN 31?


Correct Answer: B




How many Ethernet Routing Switch (ERS) 4500 switches can be connected in a single stack?


A.      4

B.      8

C.      9

D.      10


Correct Answer: B




An engineer needs to assign an IP address of 172 25 10.31 for out of band management of an Ethernet Routing switch (ERS) 8600 switch a subnet mask of  Which command line interface (CLI) command should the engineer use?


A.      ERS8600:5# config bootconfig set ip 172.26.10 36/26

B.      ERS8800:5 # config bootconfig set ip 172.25.10 36/27

C.      ERS8600:5# config bootconfig net mgmt ip

D.      ERS8600:5# config bootconfig net mgmt ip

Correct Answer: D



Download Latest Avaya 3600 Real Free Tests , help you to pass exam 100%.